RedSealMillwrightExam

Sample questions: Industrial mechanic (millwright) exam

RedSealMillwrightExam · Topics · Exam guide · Sample questions

The 35 questions of the free mini practice exam, written by us, with the correct answer. The first 10 include the full explanation and the RSOS sub-task; the full explanations of the others are in Premium access. They are not Red Seal exam questions.

1. What is the function of an overrunning clutch used as a backstop on an inclined conveyor drive?

  1. Stops the loaded belt rolling backward.
  2. Slips to protect the belt from overload.
  3. Limits the motor starting current.
  4. Varies the belt speed during operation.

Sub-task C-11.03 of the RSOS covers maintaining overrunning clutches; used as a backstop, the clutch locks when the load tries to run in reverse. It does not limit starting current, which a soft starter does, or slip at overload, which a friction torque limiter does. It cannot vary the speed either; a variable-speed drive does that.

2. What property of a grease is identified by its NLGI grade number?

  1. Its softening temperature under heat.
  2. Its base oil viscosity at 40 °C.
  3. Its type of thickener and additives.
  4. Its stiffness, by cone penetration.

Sub-task A-3.03 of the RSOS lists penetration, drop point and viscosity as separate properties of lubricants. The NLGI number classifies grease consistency, which is measured by cone penetration; a higher number is a stiffer grease. Drop point is the temperature at which the grease softens enough to drip, base oil viscosity is graded by the ISO VG number, and the thickener and additive type are not given by the NLGI number.

3. In what order are the bolts of a gasketed pipe flange tightened to compress the gasket evenly?

  1. From the bottom bolt upward on each side in turn.
  2. Around the flange in turn, to full torque in one pass.
  3. The top two bolts first, then the bottom two bolts.
  4. In a star pattern, with torque raised in passes.

Sub-task D-19.02 of the RSOS has the millwright connect process piping and components. A star (criss-cross) pattern in several passes pulls the two flange faces together evenly, so the gasket seats without a leak path. Tightening bolts one after another, in pairs or up each side tilts the flange and loads the gasket unevenly.

4. A vertical pneumatic cylinder holds a load that is not mechanically supported. What must be done before the cylinder is opened for repair?

  1. Support the load mechanically before exhausting any air.
  2. Lower the regulator pressure so the load moves slowly.
  3. Exhaust the air, then support the load once it settles.
  4. Plug the exhaust port so the piston stays in place.

Sub-task E-22.04 of the RSOS calls for a zero-energy state and mechanical lockout of components. When the air is exhausted, a suspended load descends under gravity, so it must be blocked or supported before any air is released. Supporting it afterwards lets the load drop first, a lower regulator setting still leaves the load hanging on air pressure, and plugging the exhaust port traps pressure and does not make the load safe.

5. A 3-leg sling shares a 9000 lb. load equally. Each leg is 8 ft. long and the hook is 5 ft. above the load. Using the formula sheet, what is the stress per leg?

  1. 14 400 lb.
  2. 7200 lb.
  3. 9000 lb.
  4. 4800 lb.

Formula 9 of the formula sheet: sling stress = (length ÷ height × weight) ÷ number of legs = (8 ÷ 5 × 9000) ÷ 3 = 4800 lb. 7200 lb. divides by 2 legs instead of 3, 9000 lb. ignores both the length ÷ height ratio and the number of legs, and 14 400 lb. forgets to divide by the number of legs.

6. An oil report shows high iron and a rising particle count, with no water present. What is the correct next step?

  1. Drain the oil and keep the same interval.
  2. Resample sooner and inspect gears and bearings.
  3. Add a heavier grade of oil to the sump.
  4. Replace the breather and take no further action.

Sub-task F-23.05 of the RSOS has information from the test report directed toward corrective action: rising iron and particles indicate abnormal wear of steel parts, so resampling sooner and inspecting is the sound response. Changing oil removes the evidence without curing the wear, a heavier grade does not stop it, and the breather matters for water, which is absent.

7. Which tool shows the surface temperature of a rotating coupling without touching it?

  1. Strobe light.
  2. Feeler gauge set.
  3. Thermal imager.
  4. Dial indicator.

Sub-task C-11.02 of the RSOS lists thermal imaging equipment for diagnosing couplings, clutches and brakes; it shows surface heat from a safe distance on a running machine. A strobe light freezes motion, a feeler gauge measures a gap and a dial indicator measures runout or movement; none of them reads temperature.

8. A 0.001 in. vernier caliper has its zero just past the 1.450 in. line, and vernier line 12 aligns with a main scale line. What is the reading?

  1. 1.438 in.
  2. 1.450 in.
  3. 1.462 in.
  4. 1.474 in.

Sub-task A-5.02 of the RSOS lists calipers among the precision measuring tools. The main scale gives 1.450 in. and the aligned vernier line adds 12 × 0.001 in. = 0.012 in., so the reading is 1.462 in. 1.450 in. ignores the vernier, 1.438 in. subtracts the vernier value, and 1.474 in. doubles it.

9. A receiver relief valve fitted with a test lever is due for its routine operation check. How is it done safely?

  1. Briefly lift the test lever under system pressure.
  2. Cap its outlet and raise the pressure above the set point.
  3. Lift the test lever after the receiver is vented.
  4. Back off the adjusting screw until the valve lifts.

Sub-task D-18.03 of the RSOS has the millwright verify the operation of relief valves. Lifting the test lever briefly while the receiver is under pressure, at no less than the test pressure the manufacturer specifies, shows that the disc moves freely and then reseats. Backing off the adjusting screw changes the set point, capping the outlet defeats the valve and is dangerous, and a vented receiver gives no flow to prove the valve.

10. What is the main hazard of using compressed air to blow dust off clothing or skin?

  1. Air can ignite the dust on the clothing.
  2. Air can enter the skin and bloodstream.
  3. Heated air can burn the skin badly.
  4. Air can strip the skin of its natural oils.

Safe work practices in sub-task E-22.04 of the RSOS cover the hazards of pneumatic systems, and compressed air must never be pointed at skin or used to clean clothing. High-pressure air can penetrate the skin and enter the bloodstream, which can cause serious injury. Air at shop pressure does not ignite dust, it is not hot enough to burn skin, and it does not strip skin oils.

11. What is the danger of spinning a cleaned rolling-element bearing with compressed air?

  1. The air stream magnetizes the rolling elements.
  2. The air cools the rings and removes clearance.
  3. It can overspeed the dry bearing and damage it.
  4. The air pushes the cage out of position.

Correct answer: It can overspeed the dry bearing and damage it. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

12. A millwright finds that the shock-absorbing pack on a lanyard has partly deployed after an earlier fall arrest. What must be done with the lanyard?

  1. Return it to use after a stitching check.
  2. Remove it from service and tag it.
  3. Keep it for use as a restraint lanyard.
  4. Wash it in mild soap and let it dry.

Correct answer: Remove it from service and tag it. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

13. A 20 000 lb. press will be moved along a shop floor route. What must be done first?

  1. Rely on the route used for a previous move of a similar size.
  2. Start the move slowly to find any weak areas of the floor.
  3. Assess the floor and site conditions, then plan the route.
  4. Pick the shortest route and check the floor afterwards.

Correct answer: Assess the floor and site conditions, then plan the route. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

14. Which vibration measurement is best suited to detecting high-frequency faults such as gear and rolling-element bearing defects?

  1. Shaft displacement.
  2. Overall velocity.
  3. Peak acceleration.
  4. Relative phase angle.

Correct answer: Peak acceleration. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

15. What must be done first before replacing the oil filter on a rotary screw compressor?

  1. Run the compressor unloaded until the oil cools down.
  2. Close the discharge valve and leave the motor running.
  3. Open the receiver relief valve to drain the oil.
  4. Lock out the motor and relieve the system pressure.

Correct answer: Lock out the motor and relieve the system pressure. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

16. A 3 in. diameter piston must lift a 12 000 lb. load. What pressure is needed to start the lift, ignoring friction?

  1. 424 psi
  2. 1270 psi
  3. 1700 psi
  4. 5330 psi

Correct answer: 1700 psi. The step-by-step calculation, with the formula from the exam formula sheet, is included in Premium access.

17. Black rubber dust collects inside the guard of a motor-pump jaw coupling, and the spider is hot and cracked. What is the most likely cause?

  1. Shaft misalignment at the coupling.
  2. Partly blocked pump suction strainer.
  3. Reversed rotation of the motor shaft.
  4. Low voltage at the motor terminals.

Correct answer: Shaft misalignment at the coupling. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

18. In what order are tools used to mark a hole position on a steel plate before drilling?

  1. Scriber, prick punch, centre punch.
  2. Prick punch, centre punch, scriber.
  3. Scriber, centre punch, prick punch.
  4. Centre punch, scriber, prick punch.

Correct answer: Scriber, prick punch, centre punch. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

19. Which clutch transmits torque through interlocking teeth and is engaged only when the speed difference is very low?

  1. Friction-plate clutch.
  2. Positive-contact clutch.
  3. Roller overrunning clutch.
  4. Fluid-coupling clutch.

Correct answer: Positive-contact clutch. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

20. A pump impeller is 9 in. in diameter and turns at 1800 rpm. Using Formula 11, what is its peripheral speed to the nearest 10 ft./min.?

  1. 2120 ft./min.
  2. 50 890 ft./min.
  3. 8480 ft./min.
  4. 4240 ft./min.

Correct answer: 4240 ft./min. The step-by-step calculation, with the formula from the exam formula sheet, is included in Premium access.

21. A vacuum cup drops a part while the supply pressure to the generator is normal and the vacuum reads low. What is checked first?

  1. Lubricator oil level and drip rate.
  2. Cup lip wear and leaks in the hose.
  3. Cylinder rod wiper and seal condition.
  4. Receiver safety valve set pressure.

Correct answer: Cup lip wear and leaks in the hose. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

22. What does the working load limit (WLL) marked on a sling tag represent?

  1. The maximum load the sling may carry in service.
  2. The load applied to the sling during proof testing.
  3. The combined weight of the sling and its fittings.
  4. The load at which the sling breaks when tested.

Correct answer: The maximum load the sling may carry in service. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

23. Which NDT method relies on capillary action to draw a liquid into surface-breaking cracks?

  1. Thermographic testing.
  2. Dye penetrant testing.
  3. Radiographic testing.
  4. Magnetic particle testing.

Correct answer: Dye penetrant testing. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

24. A quench-hardened chisel is too brittle and chips in use. Which treatment reduces its brittleness while keeping most of its hardness?

  1. Annealing from above the critical temperature.
  2. Tempering below the critical temperature.
  3. Normalizing from above the critical temperature.
  4. Quenching again in cold water from red heat.

Correct answer: Tempering below the critical temperature. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

25. With the plunger of a dial indicator set on a tooth at the pitch line, how is backlash measured?

  1. Turn both gears together and read the total runout.
  2. Load the drive and read the shaft end float.
  3. Rock both gears together and read the shaft deflection.
  4. Lock one gear, rock the other, read the tooth movement.

Correct answer: Lock one gear, rock the other, read the tooth movement. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

26. Why is there a pressure differential between the cut-in and cut-out settings of a compressor pressure switch?

  1. To set the highest pressure the receiver can hold.
  2. To remove moisture from the air in the receiver.
  3. To keep the intercooler outlet temperature constant.
  4. To stop the compressor from starting too often.

Correct answer: To stop the compressor from starting too often. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

27. How does a venturi-type vacuum generator produce vacuum at its suction port?

  1. Compressed air passing through a nozzle draws in air.
  2. A rotating vane pump moves air out of the port.
  3. A piston stroke enlarges a sealed chamber.
  4. Cooling trapped air lowers its pressure in a chamber.

Correct answer: Compressed air passing through a nozzle draws in air. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

28. A motor bearing runs much hotter right after a technician gave it 30 strokes of a grease gun. What is the most likely cause?

  1. The grease has too high a drop point.
  2. The base oil in the grease is too thin.
  3. Excess grease is churning in the housing.
  4. The fitting was not wiped before greasing.

Correct answer: Excess grease is churning in the housing. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

29. What is good shim practice under a machine foot during alignment?

  1. Stack thin shims to reach the height.
  2. Fold one shim to build up thickness.
  3. Use a few thick, clean, flat shims.
  4. Put the shims under the outer foot edge.

Correct answer: Use a few thick, clean, flat shims. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

30. Which condition on an alloy steel chain sling is cause for removing it from service?

  1. A light film of oil on the links.
  2. Links that are stretched or twisted.
  3. Paint worn from the master link.
  4. Dried mud that washes off the links.

Correct answer: Links that are stretched or twisted. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

31. Which NDT method can find near-surface cracks in a carbon steel shaft but cannot be used on an aluminum housing?

  1. Dye penetrant testing.
  2. Magnetic particle testing.
  3. Ultrasonic flaw testing.
  4. Eddy current inspection.

Correct answer: Magnetic particle testing. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

32. A fan still shakes at running speed after its blades were cleaned. What is the procedure for field balancing in one plane?

  1. Add weight at the highest-reading point, then retest.
  2. Trim the blade tips until vibration reads zero.
  3. Fit equal weights on each blade, then remove them.
  4. Take baseline, add trial weight, calculate correction.

Correct answer: Take baseline, add trial weight, calculate correction. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

33. Why are branch lines to tools connected to the top of a compressed air main?

  1. Condensate in the main cannot enter the branch.
  2. Less pipe length is needed for each tool drop.
  3. The main then needs no slope toward a drain.
  4. Pressure at the tool is raised by the extra height.

Correct answer: Condensate in the main cannot enter the branch. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

34. What do three radial lines on the head of an inch-series hex cap screw indicate?

  1. SAE grade 5.
  2. SAE grade 8.
  3. SAE grade 2.
  4. Class 8.8.

Correct answer: SAE grade 5. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

35. Compared with a spur gear, what added effect do the angled teeth of a single helical gear produce?

  1. Greater backlash at the pitch line.
  2. Lower load sharing between teeth.
  3. Reverse rotation of the driven shaft.
  4. Axial thrust on the shaft bearings.

Correct answer: Axial thrust on the shaft bearings. The full explanation, with the reasoning and the RSOS sub-task this question tests, is included in Premium access.

Take the free test · full question bank and mock exams with a subscription