What this topic covers
MWA A, Common Occupational Skills, as numbered in the 2017 RSOS: safety-related functions (task A-1), tools and equipment (A-2), routine trade tasks (A-3; A-3 and A-4 in the 2026 RSOS), communication and mentoring (A-4; A-8 in 2026), measuring and layout (A-5) and cutting and welding (A-6). These are original practice notes, not official material of the Red Seal Program or ESDC. Safety points are principles common to all provinces; a provincial rule is always given with its province. For settings, clearances, torques and temperatures, follow the manufacturer's specifications.
Safety, WHMIS and lockout
- PPE for grinding: safety glasses plus a face shield; a face shield alone leaves gaps below and at the sides (sub-task A-1.01).
- Safety data sheet: 16 headings in the order of Schedule 1, per section 4 of the Hazardous Products Regulations; 9 sections was the old WHMIS 1988 format (sub-task A-1.02).
- Spills: stop the source, contain the oil before it reaches a drain, report it (sub-task A-1.03).
- LOTO sequence: stop normally, isolate, lock and tag, release stored energy, then verify the zero-energy state (sub-task A-1.04).
- Group lockout: each worker puts a personal lock on the lock box; a tag alone or a shared key does not protect you (sub-task A-1.04).
Tools and access equipment
- Defective tools: tag and withdraw a tool with exposed conductors until a qualified person repairs it (sub-task A-2.01).
- Grinding wheels: the maximum wheel speed must equal or exceed the no-load speed of the grinder (sub-task A-2.01).
- Twist drill: a general-purpose drill has a 118° included point angle, 59° per lip (sub-task A-2.02).
- Work rest (Ontario): section 30 of Ontario Regulation 851 sets a maximum clearance of 3 mm, above the wheel centre line; may change, check the current regulation (sub-task A-2.02).
- Ladders: 4 to 1 ratio, 1 ft. of base offset for every 4 ft. of height to the top support (sub-task A-2.03).
Cutting and welding
- Oxy-fuel set-up: crack the cylinder valve to blow out dirt, fit the regulator, back off the adjusting screw, then open the valve slowly (sub-task A-6.01).
- Shielding gas on mild steel: an argon and carbon dioxide mix; hydrogen causes cracking in carbon steel (sub-task A-6.04).
Routine trade tasks
- Tap drill: about nominal diameter minus pitch, for roughly 75 % of a full thread (sub-task A-3.05).
- Fastener grades: 3 radial lines = SAE grade 5, 6 lines = grade 8, plain head = grade 2 or lower (sub-task A-3.05).
- Grease: mixing thickeners, such as lithium and polyurea, can soften or separate the grease (sub-task A-3.03).
- Spark test: mild steel gives long straw-yellow streams, cast iron short dull red sparks, aluminum none (sub-task A-3.06).
- Heat treatment: annealing (slow furnace cooling) softens; quenching hardens; tempering reheats below the critical temperature (sub-task A-3.07).
- Drawings: short even dashes show a hidden edge (sub-task A-3.08).
Measuring and layout
- Inch micrometer: sleeve numeral 0.100 in., each extra line 0.025 in., plus the thimble reading (sub-task A-5.02).
- TIR: the full needle swing, 0.004 in. − (−0.003 in.) = 0.007 in. (sub-task A-5.02).
- Areas: Formula 3 of the formula sheet, area of circle = π × radius², with the radius, not the diameter (sub-task A-3.02).
- Squaring a layout: Formula 6, a² + b² = c²; sides of 18 in. and 24 in. give 30 in. (sub-task A-5.03).
- Micrometer zero: close clean faces with the ratchet; it reads zero (sub-task A-5.04).
Communication and mentoring
- Mentoring steps: identify the point of the lesson, link it, demonstrate, provide practice, then give feedback and assess (sub-task A-4.02).
- Feedback: prompt and private, naming the error and the right method (sub-task A-4.02).
Sample questions (5)
1. Which combination of eye and face protection is required when grinding a weld with an angle grinder?
- Clear prescription glasses without side shields.
- Tinted welding goggles with no face shield.
- A face shield worn without safety glasses.
- Safety glasses worn under a face shield.
Sub-task A-1.01 of the RSOS requires PPE to be selected according to the job task, and grinding throws sparks and fragments that call for safety glasses plus a face shield. A face shield alone leaves gaps when debris comes from below or the side. Tinted welding goggles are for gas welding work, and ordinary prescription glasses without side shields give no impact protection.
2. How many numbered headings must a WHMIS 2015 safety data sheet (SDS) show?
- 9 sections.
- 16 sections.
- 12 sections.
- 20 sections.
Section 4 of the Hazardous Products Regulations requires the headings of Schedule 1, in order and with their item numbers, and Schedule 1 sets out 16 headings. Nine sections belongs to the old material safety data sheet format of WHMIS 1988. Neither 12 nor 20 sections matches any WHMIS format.
3. Which sequence is correct for a field level risk assessment (FLRA) before starting a job?
- Identify hazards, assess the risk, then apply controls.
- Assess the risk, apply controls, then identify hazards.
- Identify hazards, apply controls, then assess the risk.
- Apply controls, identify hazards, then assess the risk.
Sub-task A-1.02 of the RSOS requires hazards to be recognized and addressed. A hazard has to be identified first, its risk rated next, and the controls chosen to match that rating. Applying controls before the risk is rated, or before the hazard is known, means the controls are guesses and can leave the real hazard uncontrolled.
4. A hydraulic hose bursts and oil flows toward a floor drain. What should the millwright do first?
- Wipe up the oil and bin the rags as garbage.
- Flush the oil down the drain with hot water.
- Spread absorbent and report the spill after shift.
- Stop the leak and keep the oil from the drain.
Sub-task A-1.03 of the RSOS requires environmental hazards to be reported and contamination of water, air and soil to be avoided. The first action is to stop the source and contain the oil so it cannot reach the drain. Flushing spreads the contamination, waiting until the end of the shift to report delays the response, and oily rags are hazardous waste that must not go in the general garbage.
5. In Alberta, what must a worker do after the energy-isolating device is secured and before starting work on the machinery?
- Record the lock number in the shift log.
- Test the machinery to verify it is inoperative.
- Wait ten minutes for the energy to dissipate.
- Ask the supervisor to sign the lock-out tag.
Section 213 of the Alberta OHS Code states that a worker must not work on the machinery until section 212 is completed, the worker tests the machinery to verify that it is inoperative, and the worker confirms it is inoperative or made safe. Logging a lock number, signing a tag or waiting a fixed time does not replace that test. Sub-task A-1.04 of the RSOS also requires the zero-energy state to be confirmed.