RedSealMillwrightExam

🔧 Preventative and Predictive Maintenance, Commissioning and Decommissioning

What this topic covers

MWA F of the 2017 RSOS: preventative and predictive maintenance (task F-23; F-25 in the 2026 RSOS) and commissioning and decommissioning (task F-24; F-26). These are original practice notes, not material from the Red Seal Program or ESDC. Safety points are principles common to all provinces. For lubrication quantities, alarm limits and run-in periods, follow the manufacturer's specifications.

Preventative maintenance

Vibration analysis

Balancing

NDT and fluid analysis

Commissioning

Decommissioning

Take the free test · full question bank and mock exams with a subscription

Sample questions (5)

1. What is the main purpose of a CMMS in a maintenance department?

  1. Measuring shaft vibration at the bearing housings.
  2. Scheduling work orders and storing equipment history.
  3. Controlling the operating speed of driven machines.
  4. Detecting internal flaws in welded components.

A computerized maintenance management system schedules PM tasks, issues work orders and keeps the equipment history that sub-task F-23.01 of the RSOS lists as a source of maintenance information. Vibration is measured with a data collector, speed is controlled by a drive, and internal flaws are found by NDT methods such as ultrasonic testing, not by software.

2. A millwright hears a new rattling noise from a pump bearing housing during a PM round. What is the correct next step?

  1. Wait for the next round to see if it worsens.
  2. Add extra grease to the housing and carry on.
  3. Record the noise and request a work order.
  4. Replace the bearing without any further checks.

Sub-task F-23.01 of the RSOS has the millwright record information for future evaluation and repair, so the finding is logged and a work order raised. Waiting for the next round leaves the defect unreported, extra grease can mask or worsen it, and replacing the bearing without diagnosis may fix nothing and wastes parts.

3. Which type of maintenance is performed at set time intervals regardless of equipment condition?

  1. Preventative maintenance.
  2. Corrective maintenance.
  3. Predictive maintenance.
  4. Breakdown maintenance.

Preventative maintenance is scheduled by time or running hours, as listed among the types of maintenance in sub-task F-23.01 of the RSOS. Breakdown and corrective maintenance happen after a failure or defect appears, and predictive maintenance is triggered by measured condition rather than by the calendar.

4. On a scheduled lubrication route, what should be done first at a bearing grease fitting?

  1. Remove the end cover and drain the old grease.
  2. Blow out the old grease with compressed air.
  3. Wipe the fitting and confirm the grease type.
  4. Pump grease until it flows from the seals.

Sub-task F-23.01 of the RSOS has components lubricated to site and manufacturers' specifications, so the fitting is wiped first to keep dirt out of the bearing and the correct grease is confirmed. Removing the end cover to drain the grease or blowing it out with compressed air is not part of a routine greasing task, and pumping until grease flows from the seals over-greases the bearing, which can overheat it and damage the seals.

5. A fan shows a high vibration peak at 1x rpm in the radial direction, with low axial vibration. What is the most likely cause?

  1. Imbalance of the rotor.
  2. Angular misalignment.
  3. Mechanical looseness.
  4. A damaged bearing race.

A strong radial peak at 1x rpm with little axial vibration is the signature of imbalance, one of the causes of vibration named in sub-task F-23.02 of the RSOS. Angular misalignment shows high axial vibration at 1x and 2x, looseness produces many harmonics, and a race defect appears at non-synchronous bearing frequencies.

Start free

RedSealMillwrightExam · Topics · Exam guide · Sample questions