What this topic covers
MWA B of the 2017 RSOS: task B-7, planning the lift (B-9 in the 2026 RSOS), and task B-8, rigging, lifting, moving and maintaining rigging (B-10). These are original practice notes, not material from the Red Seal Program or ESDC. Safety points are principles common to all provinces; a provincial rule is given with its province and may change, so check the current regulation. For clip torque and other settings, follow the manufacturer's specifications.
Determining the load
- Load weight: from nameplates, shipping information or manuals; lug size, a sling tag or the crane rating do not give it (sub-task B-7.01).
- Hook load: add attached parts and rigging hardware: 1800 + 600 + 150 = 2550 lb. (sub-task B-7.01).
- Steel: volume × 490 lb. per ft³ (Formula 1) or × 7 849 kg per m³ (Formula 2), after converting inches to feet; a round bar uses Formula 14, volume = height × π × radius² (sub-task B-7.01).
- Centre of gravity: it must be under the hook; a load that tilts is landed and re-rigged (sub-task B-7.01).
Rigging selection and sling angles
- WLL: the maximum load in service, checked against the design factor and the actual weight; not the breaking strength (sub-task B-7.02).
- Design factor: in British Columbia, Table 15-1 of the BC OHS Regulation sets 4 for alloy steel chain slings, 5 for wire rope and synthetic slings, 10 for rigging supporting workers (sub-task B-7.02).
- Wire rope WLL: Formula 17, 6 × 19 rope = diameter² × 8, in tons for a diameter in inches: 0.75² × 8 = 4.5 tons (sub-task B-7.02).
- Sling stress: Formula 9, (length ÷ height × weight) ÷ number of legs, to a maximum of 3 legs: (10 ÷ 8 × 4000) ÷ 2 = 2500 lb. (sub-task B-7.03).
- Sling angle: a smaller angle from the horizontal raises leg tension; at 30° each leg carries twice its vertical share, while the hook load is unchanged (sub-task B-8.01).
Equipment and work area
- Load charts: capacity by boom angle and distance (sub-task B-7.03).
- Site conditions: ground, floor and environment identified before the route is planned (sub-task B-7.04).
- Power lines: approach limits and permits; the utility confirms the voltage, which sets the clearance; a wire rope tag line conducts (sub-task B-7.04).
Clips, shackles and edges
- Clip count: Formula 15, 3 × diameter + 1 up to and including 7/8 in.; Formula 16, 3 × diameter + 2 from 1 in.; round up (3/4 in.: 3.25, so 4 clips) (sub-task B-8.01).
- Clip spacing: Formula 10, 6 × rope diameter (sub-task B-8.01).
- Saddle on the live end: in British Columbia, section 15.22 of the BC OHS Regulation has the U-bolt bear on the unloaded end; re-tighten after the first load (sub-task B-8.01).
- Shackle and edges: sling eyes in the bow, hook on the pin; pad sharp edges (sub-task B-8.01).
Lifting and moving
- Test lift: a few inches, then stop: load level, rigging seated, brakes holding (sub-task B-8.02).
- Signals: one designated signal person in sight of the operator; anyone may call an emergency stop (sub-task B-8.02).
- Load path: in Ontario, section 51 of Regulation 851 requires guide ropes where uncontrolled motion may endanger a worker, and no load over a worker (sub-task B-8.02).
- Jacking: crib as the load rises; a jack alone never holds a load (sub-task B-8.02).
Inspection and storage
- Rejection: cracked, stretched or twisted chain; red warning yarns; damaged rigging tagged out. In British Columbia: 6 or more random broken wires in one rope lay (section 15.25), hook twisted more than 10° (section 15.29) (sub-task B-8.03).
- Storage: on racks, clean and dry (sub-task B-8.03).
- Examination: in Ontario, section 51 of Regulation 851 requires a competent person's examination at least once a year, recorded (sub-task B-8.03).
Sample questions (5)
1. A new gearbox arrives and no scale is available. Where should the weight used for the lift be taken from?
- The size of its lifting lugs.
- The nameplate or shipping papers.
- The rated capacity on the sling.
- The crane's maximum rated load.
Sub-task B-7.01 of the RSOS says load weight is referenced from nameplates, shipping information and manufacturers' manuals when it cannot be scaled. Lug size does not indicate weight, a sling tag shows what the sling can carry rather than what the load weighs, and the crane's maximum rating is a capacity, not the load weight.
2. What is the main purpose of a safety latch on a lifting hook?
- To keep the sling eye from slipping off the hook.
- To increase the working load limit of the hook.
- To stop the hook rotating when the load is lifted.
- To warn the rigger when the hook is overloaded.
A safety latch closes the throat of the hook so the sling eye cannot slip off when the rigging goes slack or is bumped, a basic rigging hardware practice under sub-task B-7.02 of the RSOS. A latch does not raise the WLL, does not stop rotation and has no overload-warning function.
3. Which document gives a mobile crane operator the maximum permitted load at a given boom length and radius?
- The crane inspection report.
- The manufacturer's load chart.
- The rigging inspection tag.
- The operator's daily logbook.
Sub-task B-7.03 of the RSOS requires load charts for boom angles and distance to be referred to so the equipment is not overloaded. An inspection report records the condition of the crane, a rigging tag records the rating of the sling, and a logbook records use and checks; none of them gives capacity by boom length and radius.
4. Under Table 15-1 of the BC OHS Regulation, what is the minimum design factor for an alloy steel chain sling?
- 4.
- 3.
- 5.
- 10.
Table 15-1 in section 15.6 of the BC OHS Regulation sets a minimum design factor of 4 for alloy steel chain slings, a rating that sub-task B-7.02 of the RSOS expects the rigger to take into account. A factor of 3 is below the minimum, 5 is the value for wire rope and synthetic slings, and 10 is the minimum for rigging that supports workers.
5. Two sling legs lift a load at 30° to the horizontal. Compared with a vertical lift, how does the tension in each leg change?
- The tension in each leg rises by 50 %.
- The tension in each leg stays the same.
- The tension in each leg is cut in half.
- The tension in each leg doubles.
Each leg carries half the load divided by the sine of its angle to the horizontal, so at 30° (sin 30° = 0.5) the tension is (W ÷ 2) ÷ 0.5 = W, twice the W ÷ 2 of a vertical lift, which is the sling angle effect explained in sub-task B-7.03 of the RSOS. The tension does not stay the same, is not halved, and the increase is 100 %, not 50 %.